TSA on SLP offshore oil platform

A video showing Flame Spray TSA used on an offshore platform

Metallisation MK73 flame spray systems being used to apply thermal spray aluminium (TSA) to an offshore oil platform for corrosion prevention. The platform is destined for the North Sea. Long supplies packages (30m) were used to enable sprayers to move easily around the structure and increase productivity.

Flame spray TSA onto offshore oil platform with metallisation MK73 systems, the area of TSA was approximately 1,000 sqm to 250-400 microns.

The system allowed 30m of supplied from gas the flexibility to spray areas of 27m of long main column tubulars.

TSA (Thermal Sprayed Aluminium) for CUI

The video shows the preparation and application of Thermal Spray Aluminium (TSA) to protect pipelines and vessels against atmospheric corrosion and Corrosion Under Insulation (CUI).
This clip illustrates the complete process of applying Thermal Sprayed Aluminium to deliver effective corrosion protection or an (estimated) 20+ years.

After the Thermal Spray Aluminium has been applied, the blast profile is measured and saved to be used in an audit at a later date. Next, the site is inspected with a 10X illuminated magnifying glass to check if the blast surface is clean and to identify any embedded grit particles. After this, the area is tested using dust contamination tape by placing the tape onto the surface, removing and then inspecting with a 10X magnifier.

A salt contamination test is then carried out to inspect the presence of salt on the blasted area. This is achieved through the application of an agitate test solution, then using the test pipette to ascertain the level of salt.

Afterwards, check the bond strength and thickness meets specification.

TSA is applied by the flame spray process using a Metallisation MK73 system with long supplies package to assist in accessing hard to reach areas.

Met-Clad Laser Cladding

Metallisation MET CLAD Laser Cladding System

The video gives a brief introduction to the laser cladding process, shows a selection of laser clad applications.

The video also shows how easy it is to operate and control the laser cladding process with the Metallisation MET CLAD laser cladding control system. The Metallisation MET-CLAD laser cladding system takes control of all of the laser cladding process and simplifies it via a reliable and repeatable touch-screen control system.

More detail can be found on the MET-CLAD system at /products/laser-cladding/metclad.html

LPG cylinder metal spraying

This video shows the automated zinc spraying of gas cylinders (LPG cylinders) with Metallisation ARC528E automated arc spray systems. This can be onto brand new cylinders or on reclaimed/repaired cylinders. The zinc coating is applied to give longer corrosion protection to cylinders compared to paints alone. The paint or powder coating are often damaged during manual handling and the zinc coating beneath provides a sacrificial coating.

Leading the Battle Against Rust

Examples of corrosion protection with both ARC and Flame Spray Systems on a variety of substrates.

Typical Applications

TSZ of wind towers with ARC528E/S1500.
TSA on offshore oil platform.
TSZ of wind towers with ARC140/S350.
TSZ of ship with ARC150/S500.
TSZ of fishing boats with ARC150/S500.
TSA for corrosion under insulation with MK73.
Spraying with the Flame Extension.
TSA of footbridge with MK73.
Typical equipment set-up – Flame.
Typical equipment set-up – ARC.

HVOF Turnkey Installation at B&B Coatings Ltd

HVOF Turnkey Blast and Spray Installation at B&B Coatings

This video gives an overview of a turnkey blast and HVOF thermal spray installation, installed at B&B Coatings Ltd in Yorkshire, UK.

The project was the result of a co-operation between SciTeeX in Poland and Metallisation Ltd to supply a blast room, HVOF spray room, extraction, robot and MET-PCC(HVOF-L) liquid fuel HVOF system.